| switch |
INI-entry |
default |
meaning |
| Common settings |
| |
alignwindows= |
0 |
aligns the program windows on startup |
| -b |
playbeep=0|1 |
0 |
generates a 'beep' if a unknown cell is used |
| -u<x> |
updfreq=x |
2000 |
applies a updatecycle of x ms |
| -x |
hexoutput=0|1 |
0 |
show data as hexadecimal values |
| -nstk |
|
|
suppress the usage of the SIM-Toolkit-Feature with Siemens
phones |
| |
regname=
regkey=
regexp= |
|
enter your registration key here |
| Communication
settings |
| |
baudrate= |
19200 |
sets the communication speed |
| -p<x> |
comport=x |
1 |
COM-Port to use, x is the portnumber |
| -fbus |
fbusmode=0|1 |
0 |
use the FBUS-driver for Nokia-phones |
| -at |
|
do not use FBUS, use AT-Commands |
| -i<x> |
inidelay=x |
200 |
when having problems connecting to the phone (perhaps via IR): x is
the time in ms to wait between the opening of the port and the sending of the
first command |
| |
autoretry=0|1 |
0 |
if the communication with the phone fails during operation, the software
does not display this annoying error message, but tries to establish the
connection again |
| -d |
debug=0|1 |
0 |
switch on the debugmode if there are problems |
| Special settings |
| |
testctarget= |
|
M20 only : target for testcall |
| |
testctime= |
20000 |
M20 only : duration of testcall in ms |
| |
testcdelay= |
3000 |
M20 only : delay for call setup |
| Logfile settings |
| -t |
trace=0|1 |
0 |
start the cell-logging at once |
| |
showcb=0|1 |
0 |
starts CB-logging at once |
| |
smscbshowtime=0|1 |
0 |
(registered version) the reception time for SMSCB-messages is
displayed in the SMSCB-window |
| |
tabisseparator=0|1 |
1 |
(registered version) a semikolon (...=0) is used as separator
character in logfiles instead of TAB (...=1) |
| |
logging=[0..3] |
0 |
(registered version) does some more logging beside the standard logfiles
for visited cells and netmonitor data. You may use:
| 1 |
0000 |
1 |
1 |
1 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
log cell, RX level |
|
( 1 ) |
| |
|
|
|
|
|
log cell, RX level, neighbor cells |
|
( 2 ) |
| |
|
|
|
|
|
log cell, complete nBCCH list |
|
( 4 ) |
| |
|
|
|
|
|
additionally log position |
|
( 128 ) |
|
| |
senderspender=0|1 |
1 |
generates a special logfile for 262 07 (VIAG Interkom) |
| |
logbufferoff= |
0 |
switches off buffered logging |
| |
logbuffersize= |
100 |
the size of the logging buffer in entrys |
| |
logbufferflush=60 |
60 |
the amount of used logbufferentrys to be reached before flushing the
logbuffer (in percent) |
| |
usegps=0|1 |
0 |
(registered version) specifies if the program should try to establish a
connection with a GPS-receiver |
| |
usegps_addr= |
127.0.0.1 |
(registered version) the IP-address to get positioning data from. This
defaults to the own computer |
| |
usegps_port= |
2947 |
(registered version) specifies the port where the 'GPS-Beacon' listens |
